High Voltage
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500. AKA: HV
See Also: High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, HV
-
product
Single Channel High Voltage Linear Amplifier
F20A
The F20A is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of ±150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Hi-Z HV Safety Voltmeters
B-1013-4
These Hi-Z® HV Safety Voltmeters are for Power Lines, Electric Cars, Electric Trolley and other High Voltage AC & DC detection and measurement. Emergency Crews can use these voltmeters to detect voltage presence warning. They will accurately measure AC and DC voltages.
-
product
DC HV tester/ hipot
Wuhan Fanke Transformer Manufacture Co., LTD
1) DC HV tester/ hipot tester/portable-type2) Suitable for DC HV. test or leaking current test
-
product
Medium Power Programmable DC Electronic Load(600W~3000W)
FT63200A/E
Shenzhen FaithTech Technology Co., Ltd.
The FT63200A/E series of Medium power programmable DC electronic load is designed for high reliability and high power density. It can achieve 2U/3kW, which is twice of the power density of the conventional load. The FT63200A/E series has three voltage ranges of 150V, 600V and 1200V, with a single power range from 750W to 3kW. Its wider working range, extremely fast dynamic frequency, effectively increase the testing capability and application range. The whole series of products have strong overload capacity, instant over power pull up to twice the rated power, can effectively reduce the test cost.
-
product
Test Sets For Diagnostic Testing
Test Sets For Diagnostic Testing are designed to test Oil Resistivity, Tan Delta, High Voltage Surge Comparison, etc. These test sets are automated instruments used to measure electrical features to insulate transformer oil, liquids and varied other insulating materials. They are ideal for revealing different localized problems and varied weak spots in the insulation. These modern testing sets are designed to provide high accuracy in results. In addition to this, they are easy to maintain testing sets available to ensure accurate readings.
-
product
LXI High Voltage Switching - 3-Bank, 1-Pole, 6:1 Multiplexer Plugin Module
65-231-910
The 65-231-910 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
Tap Adapter
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Alth...show more -
product
Resistor Calibration Box
RCB-411
Standard Electric Works Co., Ltd
● The RCB-411 is used to verify and proof High Voltage Insulation Testers. Both Analogue and Digital Insulation Testers can be calibrated.● Caution: a. Before testing, make sure the front panel, terminals are clean and dry. If not, wipe them with cloth. b. Use high voltage silicone wires. Otherwise the reading will be incorrect.
-
product
Charge Integrator Amplifiers
AD8488
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
product
MPOD HV Module
WIENER presents with Mpod a new, universal multi-channel low voltage (LV) and high voltage (HV) computer controlled power supply system. Offering highest channel density the MPOD mainframe can house up to 10 plug-in modules which can be mixed in type and parameters. Up to 480 individually controlled high voltage channels are available in one mainframe
-
product
PXI/PXIe High Density 2A Multiplexer, 8-Bank, 16-Channel, 1-Pole
40-614D-003
The 40-614D-003 (PXI) and 42-614D-003 (PXIe) 8-bank, 16-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Cable Assy 37-Pin D-Type M/F 1m HV
40-970-037-1m-MF-HV
37-Pin Male to Female D-Type Cable Assy - High Voltage, 1m Long.
-
product
Bipolar Supply Voltage Output D/A Converters
Analog Devices is an industry-leading provider of bipolar d/a converter solutions offering exceptional 1 ppm performance and optimized feature sets to ensure quick and easy deployment of bipolar converters across a range of end applications. With a comprehensive portfolio of bipolar DACs fabricated using proprietary iCMOS® process technology, ADI has enabled the development of high performance ICs at high voltage levels while simultaneously reducing package size and power consumption. By bringing together the many benefits of integration, ADI’s bipolar DACs reduce design time and system complexity.
-
product
High Voltage Snubber Capacitor
STP-01RN / STP-01RB
This series of capacitors is Plastic Enclosure, Dry construction design and doesn't have leakage problem when compared with traditional Metal Enclosure Oil impregnated capacitors.Handle high surge current, RMS current and surge voltage with Temperature up to +105CCapacitance : 0.25uF - 60uF ( can be customized )Voltage range : 900Vdc to 5,300Vdc / 280Vrms to 1,600VrmsRMS Current - Irms : up to 80Armspeak to peak pulse current - Ipp : up to 15,000AppTemperature ranges : +85C / +105C
-
product
Thick Film Passive Element
GBR-403
GBR-403 series high voltage resistors are made in a thick film technology on ceramic substrates (Al2O3 96%). These elements are used in high voltage applications requiring high stability and resistance.
-
product
PXI 2A Multiplexer, 2-Bank, 64-Channel 1-Pole
40-614-010
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Matched Transistors
Analog Devices offers dual and quad transistors with excellent matching characteristics. Offset voltages, temperature drift, and hFE matching are individually tested to data sheet specifications. Device performance is guaranteed over industrial and military temperature ranges. Each of these devices is an excellent choice as an input stage for an amplifier or in log/antilog circuits. ADI’s matched transistors offer low noise and high gain, with characteristics approaching an ideal transistor.
-
product
M-LVDS (Multi-Point Low Voltage Differential Signaling)
M-LVDS (multipoint low voltage differential signaling) is a multipoint high speed differential electrical interface with support for up to 32 nodes. Analog Devices M-LVDS products offer the industry’s highest ESD performance transceivers with high noise immunity receivers and extended common-mode range. These products are ideal for applications where designers need to transmit at data rates up to 100 Mbps or 250 Mbps to multiple nodes.
-
product
AC Ionisation
Fraser Anti-Static Techniques Ltd
A market-leading range of AC static eliminators with external high voltage power units.
-
product
IND AC/DC CAT IV TRMS Clamp Meter
ACDC-3400
The Amprobe ACDC-3400 clamp multimeter is CAT IV rated to add an extra level of safety for high voltage, industrial or utility testing applications. It is an AC/DC current clamp meter and a voltage meter all in one.
-
product
10:1 500 MHz 10 MOhms Passive Probe
PP005A
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MO. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m HV, Exit Away From Pin 1
A050DM4-C-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
LXI High Voltage Switching - 4-Bank, 1-Pole, 4:1 Multiplexer Plugin Module
65-231-913
The 65-231-913 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
Partial Discharge Test Equipment
Wuhan Huatian Electric Power Automation Co., Ltd.
Partial discharge detectors for high voltage equipment.
-
product
HV Test Transformer
GTU-800KVA/220KV
Wuhan Sangao Electrical Test Installations Limit Co.
SF6 gas -filled testing transformers are especially designed for GIS in the factory and on-site test,and for testing all GIS switchgears and GIS components such as insulators,insulating tension pole,GIS voltage transformer and so on,the PD test can be performed under the general environment because of the merits of encapsulation ,the PD level of our equipment can be lee than 3pC,and it can be added a HV bushing to perform the withstand voltage test at the same time.
-
product
Contunuity Tester With Audio Warning
CT-01
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Graduall
-
product
Capacitor Tester
MIG1212CAP
MIG1212CAP is specially designed for high voltage test on X / Y capacitors with impulse voltage approximate 1,2/50 µs up to 12 kV in accordance with IEC 60384-14 Ed.4. The MIG1212CAP comprises two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape of approximate1,2/50 µs and are combined in an 8 unit high 19" rack. IEC 60384-14 and EN 132400 define the generator.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 1m, HV
40-972-037-1m-MU-HV
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
High Voltage Pulse Attenuators
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
product
NI-9236, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
779994-02
10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 V rms transient isolation, providing high‑common‑mode noise rejection and increased safety.
